We may earn revenue from the products available on this page and participate inwards affil
We may earn revenue from the products available on this page and participate inwards affiliate programs.
Corrosion, leaks, or sticky handles are a few signs y’all desperately call for to supplant your kitchen faucet amongst a new one. Just non liking the look of it is some other totally valid argue. Whatever led yous to the decision to replace yours, know that y’all mightiness not accept to expect to phone call a plumber to make the telephone exchange. Replacing your kitchen faucet on your own is possible, says Carly Carey, a tertiary-twelvemonth plumbing apprentice at Erik Nelson Plumbing inward Minnesota too a pro at Matriarchy Build. (Psst: You can volume a consultation with Carey or any other Matriarchy plumber through the fellowship’s site if yous want extra guidance). “As long equally you lot take a shutoff that y’all know plant, this is a job that any homeowner tin can make,” she says.
Going the DIY road tin can relieve y’all anywhere betwixt $45 as well as $400 on labor costs, according to HomeAdvisor, but it’sec also rewarding to have your renovation into your own hands—too become a piffling more than familiar amongst the “spooky” cabinet underneath your sink. Carey walks us through the procedure, pace-past-pace, below.
The Supplies
- 100% silicone
- New faucet (run into our favorites hither)
- Adjustable crescent wrench
- A tarp or rags
Step ane: Check Out Your Current Setup
Don’t caput to the hardware store simply nevertheless. First, figure out what kind of faucet you lot involve—your choices will be limited by the number of mounting holes present about your sink. In virtually instances, at that place volition be one hole (for a single-grip faucet) or iii holes (for a dual-hold faucet). “If y’all currently take three holes, you lot could buy a i-hole faucet that has a plate that would cover the other ii holes, simply you couldn’t get from i hole to three holes,” notes Carey.
Step 2: Get Familiar With Your Shutoffs
The entirely mode this DIY is possible is if y’all take reliable, under-sink shutoff valves. If your habitation is older and does non boast the plumbing for yous to isolate only the kitchen faucet’second H2O connectedness, Carey recommends calling a professional person to install a novel shutoff for it, equally it’ll salvage you headaches down the road.
Open up the cabinet below the sink together with withdraw everything inside. You should run across a few things: a PVC tube (the sink drain pipage) together with ii “threads” (your hot- and common cold-H2O lines) connected to ii pipes that see either the wall or the flooring. At these connectedness points, yous’ll probable encounter a knob or lever—these are your shutoff valves. If it’s a knob, turn it clockwise to turn the water provide off. If it’sec a lever, flip it so it’s perpendicular alongside the piping.
Tip: A common mistake Carey sees homeowners brand is non knowing where their dwelling’sec main shutoff is (or just knowing if it plant). Most likely, you lot’ll be able to locate it inwards the basement or garage (where the principal H2O occupation from the city enters the family). “Plumbing can go wrong, then being able to close off all the water is actually helpful,” she says.
Step three: Remove the Old Faucet
After you’ve successfully cut off your water access, drain the water from the electric current faucet past turning the faucet handles to the “on” place.
Lay down a tarp, newspaper towels, or rags on the flooring as well as inwards in addition to around the cabinet. Next, disconnect the assembly parts that are property the faucet to the countertop in a higher place using an adjustable wrench. Then, amongst your wrench, detach the hot- as well as cold-H2O provide threads. There volition likely live more or less remainder water in them, so let them to drain onto your tarp or towel until dry out. Remove the mounting nuts that connect the faucet to the sink as well as accept out the faucet.
Step iv: Clean together with Prep for a Fresh Connection
Once the hoses are disconnected, make clean the area where y’all’ve removed the faucet. Oftentimes, in that location will live approximately gunk built up or debris from corrosion. To ensure a watertight seal for your new faucet, Carey applies 100% silicone around the acme surface of where the new faucet volition get too as the receipt underneath.
Step five: Attach the New Faucet
Each faucet is unlike, and so y’all’ll desire to follow the instructions that come up amongst the new fixture carefully. Typically, though, you lot’ll want to thread the novel faucet downward into the countertop hole(s) too get down reattaching the H2O-render lines alongside your wrench, making sure that you attach the hot-water job to the hot-water valve together with the cold-water line of work to the cold-H2O valve. It’sec helpful to have an extra yoke of hands around every bit you lot tighten the connections, every bit it’ll crusade the faucet itself to twist together with plough to a higher place. “Have I installed faucets past myself? Yes. Is it rattling slowly? No, it’sec much easier when you take person else around,” says Carey. Wipe upward whatever of the silicone that power accept seeped out of the sides underneath the faucet. Finally, slowly turn the water on together with check for whatsoever leaks.